2* 400G CFP2 Muxponder for 2U DCI BOX
Product Overview
HYD Technology’s 2*400G CFP2 muxponder offers an 8*100G service access being a module designed with perfection to cater to the optical fiber link.
This muxponder can offer a wavelength realization of the CFP2 coherent optical module; hence, the wavelengths may be converted into DWDM standard optical signal-based wavelength. There is an interconnection with the DWDM multiplexer and demultiplexer, which helps realize the wavelength division to multiplex the transmission.
It offers the solution for resolving the transmission lines’ problems, which lack fiber resources.
- It offers support for the wavelength conversion with the DWDM transmission.
- Its architecture is highly flexible and has the basis of 400G pluggable modules of coherent opticals.
- The single card it has may support 100G 8 channels, and the line side has support for the 2 channels.
- It also supports client-side service access and FEC modes on the line side.
- MSA pluggable standard modules are supported.
- 400G and 200G metro are also supported with a long haul application of 400 km and 1000 Km, respectively.
- If any enquiry ,please contact HYD TECHNOLOGY .
System Parameter | Technical Index |
Maximum capacity | 2*400G bidirectional/unidirectional transmission |
Wavelength (frequency) range | DWDM ITU-T G.694.1 Grid, C-band, with flex-grid support |
CFP2 DCO 400G Optical Transmitter Specifications | |
Modulation | DP-QPSK@100G, DP-16QAM@200G, DP-QPSK@200G, PM-16QAM@200G, PM-16QAM@400G, PCS-16QAM@400G |
Transmitter output power range | +5~-10dBm |
Transmitter OSNR | 34dB/0.1nm(OSNR at transmitter output (in-band)) |
Channel spacing | 75GHz |
Optical return loss | 27dB |
Max. -3dB spectral width | 0.6nm |
Min. SMSR (side mode suppression ratio) | 37dB(Measured over +/-2.5nm range around the target frequency with 0.06nm RBW without modulation.) |
Laser line width | 100~300kHz(FWHM-full width at half maximum of power density spectrum of CW.) |
CFP2 DCO 400G Optical Receiver Specifications | |
Input power range | -12~0dBm(Signal power of the selected channel) |
OSNR Sensitivity | 22dB/0.1nm(At internal FEC threshold (post FEC BER < 10-15), at optimum input power as specified above.) |
Receiver sensitivity | -21dBm(Minimum input power needed to achieve post FEC BER < 10-15 when OSNR > 35dB and internal FEC enabled.) |
CD tolerance | 36000ps/nm(With less than 0.5dB OSNR penalty at FEC threshold.) |
PDL tolerance | 3.5dB PDL tolerance under the following conditions: 1) PDL applied before noise loading; 2) Change in SOP is <=1 rad/millisecond; 3) With additional 1.5dB OSNR penalty. |
Input power transient tolerance | 3dBm(Optical input power transient tolerance Less than 0.5dB OSNR penalty if the received power is within input power range and rise/fall times of power change (defined by 20-80%) of 50μs or slower.) |
Channel spacing | 75GHz |
Optical return loss | 27dB |
| |
Service access types | 100/200/400GbE, OTU4, OTUC1/OTUC2/OTUC4 and FlexO |
Dimensions (mm) | 177(W)*40(H)*225(D) |
Working temperature | -10℃~70℃ |
Storage temperature | -40℃~80℃ |
Relative humidity | 5%~95% no condensation |
Safety and EMC | Compliance with FCC, UL, CE, TUV, CSA standards |
Power consumption | <78W |
Applications
HYD Technology has developed this module for Ultra-long-haul Data Center Interconnection Coherent Optical networks. It offers a very extensive bandwidth and, at the same time, is suitable for long-haul applications where long distances are needed to be covered by the optical fiber network.
